DECODER HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. Make a RF Transmitter and Receiver With HT12E & HT12D: Would you like to With the help of our friends HT12E (ENCODER) and HT12D (DECODER) and a. The HT12D is a 2^12 decoder in 18 pin DIP package. This decoder is a series of CMOS LSIs for remote control system applications. It is paired with Holtek’s.

Author: Masar Baran
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Medical
Published (Last): 25 November 2005
Pages: 391
PDF File Size: 10.57 Mb
ePub File Size: 9.22 Mb
ISBN: 903-8-80552-913-6
Downloads: 14194
Price: Free* [*Free Regsitration Required]
Uploader: Melrajas

To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Interface SD Card with Arduino.

Submitted by admin on 27 October The IC has a built in oscillator. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address declder 8-bit has to be set using the pins A0 to A7. A valid transmission in indicated by a high signal at VT pin. It is very important that your Decoder should have the same address of that of the encoder. The IC is should be powered by fecoder pin 18 and the ground pin pin 9 is grounded. They are paired with 2 12 series of encoders. It is mainly provided to interface RF and infrared circuits.

Related Posts  LIBRO ESCUCHAR MUSICA AARON COPLAND PDF

Supply voltage; 5V 2.

Connected to the Ground of circuit. This high-density System-in-Package SiP integrates controller, power switches, and support components. Valid transmission; active high. TL — Programmable Reference Voltage. If any valid data is received they can be obtained from these four pins. These are the 8-bit address bits, which is used to protect your data. Dfcoder data on 4 bit latch type output pins remain unchanged until new is received.

HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Choosing Battery for Robots. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data ht12c.

The serial input data is compared with the local addresses three times continuously. SPI Module of Arduino. This pin powers the IC should use only 5V. They can also be connected to LED to physically view the received data.

HT12D Decoder IC

Interface GPS with Arduino. Virgin Galactic — Commercial Space Flight. What is Web Browser. We should set the bits in same pattern on Encoder and Decoder Decofer to pair them.

It is not mandatory to use it. Arduino based GPS receiver. For decoding a data the IC will requires an decoeerluckily this IC has one in-built. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. Choosing Motor For Robots. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. This oscillator can be used by connecting these two pins through a 1M Resistor.

Related Posts  93C46 DATASHEET PDF

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

This pin will go high when a data is received. The Encoded 12 bit output data obtained from HT12E has to be given here. Skip to main content.

If you want security you can connect any of the 8 pins to 5V to make it high. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. In simple terms, HT12D converts the serial input into parallel outputs.

The decodr data code is decoded when no error or unmatched codes are found.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. These two ICs together form an Encoder and Decoder pair.